Alexor PC9155D-433 Instalační příručka stáhnout pdf (Strana 55)

5.3 Programming Descriptions

5-31

[030] Zone Loop Response

[101]-[134] Zone Attributes

The following options can be enabled or disabled for each zone. Pressing [9] in one of these sections brings the installer to the upper bank (attributes 9 to 16). From

the upper bank, press [9] to return to the lower bank (attributes 1 to 8).

Option Description

[1]

ON: Zone 33 is Fast Loop Response: Zone 33 has a fast loop response (36 ms).

OFF: Zone 33 is Normal Loop Response: Zone 33 has a normal loop response (400 ms).

[2]

ON: Zone 34 is Fast Loop Response: Zone 34 has fast loop response (36 ms).

OFF: Zone 34 is Normal Loop Response: Zone 34 has normal loop response (400 ms).

[3]-[8]

For Future Use

These attributes override default settings. Do NOT change fire zone attributes from their default settings.

Option Description

[1] Bell Options

ON: An alarm activates the bell output.

OFF: Silent alarm.

If a zone is set for silent alarm, and 2-way Audio (attribute [9]) is enabled, the audio session will only be Listen-in. This means the central station

operator can not speak back through the system to the end user. (This applies to the PC5950 audio verification module only).

[2] Bell Type

ON: The bell output is steady when the zone is in alarm.

OFF: The bell output pulses when the zone is in alarm.

[3] Chime

ON: The keypad chimes when the zone is violated and when the zone is secured.

OFF: The zone does not chime the keypad.

[4] Bypass

ON: The zone may be manually bypassed.

OFF: The zone can not be bypassed.

[5] Force Arming

ON: The system can be armed with the zone violated. The zone is temporarily bypassed and, when secured, is monitored by

the system.

OFF: The system cannot be armed if the zone is open.

[6] Swinger

Shutdown

ON: When the zone goes into alarm for the number of times programmed in the Swinger Shutdown Counter (see section

[377]), it shuts down with no further transmissions sent to the monitoring station. The bell follows Swinger Shutdown if pro-

grammed.

OFF: Swinger Shutdown is disabled. All alarms are transmitted and do not follow the Swinger Shutdown Counter.

If a zone is in Swinger Shutdown, and this attribute is disabled, then re-enabled, the zone will no longer be in Swinger Shutdown.

[7] Transmission

Delay

ON: Reporting of zone alarms are delayed for the programmed time in section [377] after the zone goes into alarm. If a valid

access code is entered within this time, no alarm signal is communicated.

OFF: When an alarm occurs, the reporting code is transmitted immediately.

[8] Cross Zone

ON: The zone is enabled for cross zoning.

OFF: The zone is not enabled for cross zoning.

[9] 2-way Audio

Applies to 2-way Audio Verification Module (PC5950)

ON: The zone initiates a 2-way audio verification session with the central station.

OFF: The zone does not initiate a 2-way audio session.

[10]-[13]

For Future Use

Options [14] to [16] are used for zones 33 and 34 exclusively. If more than 1 option is enabled for options 14, 15, and 16 the lowest attribute number will take pre-

cedence. If Options 14 and 15 are both enabled the zone follows the NC loop configuration.

[14] Normally

Closed

Loops

ON: The zone follows the Normally Closed (NC) loop configuration.

OFF: The zone does NOT follow NC loop configuration.

[15] Single End of

Line (SEOL)

Resistors

ON: The zone follows the SEOL zone configuration.

OFF: The zone does NOT follow SEOL zone configuration.

[16] Double End of

Line (DEOL)

Resistors

ON: The zone follows the DEOL zone configuration.

OFF: The zone does NOT follow DEOL zone configuration.

1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 87 88

Komentáře k této Příručce

Žádné komentáře

Alexor PC9155D-433 Instalační příručka Strana 55

Komentáře k této Příručce

Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Alexor PC9155D-433